The Curt Universal Truck Bed Extender with Fold-Down Tailgate, part # C57WR, is easily disassembled, for compact storage, but it was not designed to be stored in the truck.
I have included a video installation link and a video review link below. view full answer...
Yes it does; I have added a photo for you showing the finished installation of the Curt extender:
- Curt Universal Truck Bed Extender with Fold-Down Tailgate # C57WR
As you can see, the # C57WR does install on the inside of your Ram's truck bed, and I have also added a link below to a video install and the instructions for you to check out. view full answer...
The Malone Axis Load Roller for Malone Truck Bed and Roof Load Extender - 42" Long, part # MAL52VR, that comes with the Malone Axis Truck Bed and Roof Load Extender with Load Roller, part # MAL32VR, is fixed in length. It does not extend in and out. You will have to remove this when the extender is at a length less than 42".
I have included a product description link and a video review link below. view full answer...
Drilling is required for installation of the Topline Bed Extender # BX4004-01, but the installation instructions indicate that the Ford F150 full size trucks have tailgates with two holes on each side that can be used. If you remove the screws from these holes, you may use them instead of drilling, but you will still need to drill the aft hole in the tailgate, see drawing link.
The bed extender will work with plastic bed liners. If your trucks plastic bed liner includes a tailgate cover... view full answer...
When not in use you can pretty easily remove the Curt Universal Truck Bed Extender with Fold-Down Tailgate # C57WR from the truck it is installed on. It's only three pieces and it disassembles pretty easily. view full answer...
The referenced Topline Fold Down Truck Bed Extender # BX4004-01 is a correct fit for your 2014 Ram 1500. Installation instructions are linked for you at right. Tools required include a drill and bits, hammer and center punch, 5/32-inch Allen wrench and a grease pencil. You will need to trim your bed liner in the spots on the tailgate where the installation brackets mount.
Installation time is hard to predict. I would say that about an hour should suffice for a first-time installer but... view full answer...
The Topline Bed Extender, # BX4004-02, will likely interfere with ATV ramps if it is left on your tailgate. The good news is that this bed extender is easily removable. The bed extender attaches to the side brackets with two release pins. Simply remove the release pins to move the bed extender out of the way when you load your ATV. I do not recommend leaving the bed extender attached when you load your ATV.
Check out the installation video that I have attached for this bed extender. We... view full answer...
Yes, with the Bestop Supertop Collapsible Truck Bed Cover # B76317 you can operate the truck with the cover extended or collapsed.
The top requires just one person for an easy, no-drill installation and can even increase fuel efficiency up to 10 percent by cutting down on tailgate drag. And a rear tailgate bar enables users to open the tailgate without unzipping or removing the rear window. view full answer...
The Truck Bed Extender # BX4004-02 can be folded down on the tailgate but won't be flat. You can remove all but the outer brackets to allow lumber or other cargo to lay across your tailgate. As long as it is between the brackets you will be fine. It is designed for an easy install/remove.
I attached an install video for you to check out for more info as well.
The Extreme Gate bed extender has been discontinued. view full answer...
The Topline Bed Extender you referenced, part # BX4004-02 is width-adjustable and will indeed fit your 2010 Dodge Dakota if the plastic liner you refer to covers a steel tailgate. You would need to drill through the liner to attach the bed extender, but the liner can remain in place.
I have provided a photo showing the extender mounted to a tailgate that has the plastic liner. view full answer...
In order to attach the brackets from this Fold Down Truck Bed Extender # BX4004-02 to the tailgate of your 2003 Dodge Ram you will need to drill 4 holes in the tailgate, insert the turn nut into the drilled holes and then insert allen bolts through the brackets to the turn nuts and tighten them.
I will send you a separate email that has instructions for this product for you to check out also. view full answer...
The rubber bed and tailgate mat in your 2011 Dodge Ram Laramie will not prohibit the installation of the Topline Bed Extender, item # BX4004-02, on your pickup, but you may need to trim the bed mat for installation.
Trimming is a decision that will have to be made at the time of installation, since we have not had the opportunity to install this item on a truck with a rubber bed mat yet. view full answer...
I spoke with my contact at Topline and we recommend that you remove the Truck Bed Expander, # C57WR, before loading an ATV into the bed of your truck. The expander is easily removed with just the release of two pins.
I have attached a video for you to check out. view full answer...
The base rails for a fifth wheel hitch cannot be installed over plastic bed liners. Plastic bed liners must be cut out of the way to provide metal to metal contact. The base rails may be installed on a spray-in bed liner. I am including a link to an excellent video of trimming a bed liner for fifth wheel rails.
The correct base rails and mounting brackets for your 2008 Toyota Tundra Extended Cab with the 8 foot bed will be the Reese Fifth Wheel Installation Kit, part # RP30035-309. This... view full answer...
No, there is no drilling required to install any component of the Malone Axis Truck Bed and Roof Load Extender with Load Roller - 2" Hitches # MAL32VR or just the Malone Axis Load Roller for Malone Truck Bed and Roof Load Extender - 42" Long # MAL52VR.
I went ahead and attached a video that shows the pre-drilled holes on the uprights to install the rollers at timestamp 13:30. view full answer...
The anti-rattle bracket that comes with the Malone Axis Truck Bed and Roof Load Extender # MPG907 isn't a necessity but it is good to have as it reduces the amount of movement you'll see with the extender so I definitely recommend using it.
You can also swap it out for a tool-free anti-rattle device like the Curt # C27UR or Brophy # RHSB to help speed things up.
Attached are some review videos for you to check out. view full answer...
Depending on the brackets and rails that were used to install the 5th wheel your rails could be installed in a close range of measurements.
If your hitch was installed with the universal mounting brackets # RP30035 then your rear most rail should be 28-5/16 inches from the rear edge of the bed on your 2001 Ford F-250 Long Bed. I have linked a diagram from the instructions for you to better see. The center of rail to center of rail distance should measure 22 inches.
If your hitch was... view full answer...
The Erickson Big Bed Load Extender for 2" Hitches - 400 lbs # EM07600 is a fairly strong accessory. It is not recommended to add a wheel to this product and it would void the manufacturer warranty. Most other products rated for this application are rated at 350 lb load capacity so the Erickson extender is a little beefier. When in use it measures 52-1/2" long x 48-1/2" wide.
I recommend using ratchet straps like the Erickson Re-Tractable Ratchet Straps w/ Push Button Releases - 1"... view full answer...
I assume by Tahoe you are referring to a 1986 Chevy Suburban and you can use the Erickson Big Bed Junior Load Extender # EM07605 so long as you are comfortable with the rear of your Suburban being open.
There are some measurements you should be aware of to ensure you have the proper clearance; the Load Extender # EM07605 will extend 4 feet from your your hitch receiver and can adjust in height from 17" to 24".
To use the extender you also need Pin and Clip # PC3 to secure it to your hitch... view full answer...
I have some information for you on how to install the Thule TracRac Contractor Truck Bed Ladder Rack # TH14750, but unfortunately we do not have any instructional videos available at this time.
I can tell you that it does require some drilling to install- You'll need to drill into the truck bed rails, as well as one hole for each stand into the bed of the truck. If you have a bedliner on your 2013 Ford F-150, you will have to trim back the bedliner in order to install this ladder rack.
The... view full answer...
Go To Results